- From: Juan Pablo Carbajal <desalta_at_hotmail.com>
- Date: Mon, 19 Jul 2004 10:12:07 -0300
Here is the pnpdump output:
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI
-DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier 61 00 a9 19 d3 00 26 23 39
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 61 00 a9 19 d3 00 26 23 39)
# Vendor Id NIC2600, Serial Number 11082195, checksum 0x61.
# Version 1.0, Vendor version 0.0
# ANSI string -->National Instruments, AT-MIO-64E-3<--
#
# Logical device id NIC2600
# Device supports I/O range check register
# Device supports vendor reserved register _at_ 0x39
# Device supports vendor reserved register _at_ 0x3a
# Device supports vendor reserved register _at_ 0x3c
# Device supports vendor reserved register _at_ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE NIC2600/11082195 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0020
# Maximum IO base address 0xffe0
# IO base alignment 32 bytes
# Number of IO addresses required: 32
# (IO 0 (SIZE 32) (BASE 0x0020) (CHECK))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# First DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 5))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0020
# Maximum IO base address 0xffe0
# IO base alignment 32 bytes
# Number of IO addresses required: 32
# (IO 0 (SIZE 32) (BASE 0x0020) (CHECK))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# First DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 5))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0020
# Maximum IO base address 0xffe0
# IO base alignment 32 bytes
# Number of IO addresses required: 32
# (IO 0 (SIZE 32) (BASE 0x0020) (CHECK))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0020
# Maximum IO base address 0xffe0
# IO base alignment 32 bytes
# Number of IO addresses required: 32
# (IO 0 (SIZE 32) (BASE 0x0020) (CHECK))
# *** ERROR *** No IRQ specified!
# End dependent functions
(NAME "NIC2600/11082195[0]{National Instruments, AT-MIO-64E-3}")
# (ACT Y)
))
#
# Logical device id NIC2600
# Device supports vendor reserved register _at_ 0x39
# Device supports vendor reserved register _at_ 0x3a
# Device supports vendor reserved register _at_ 0x3c
# Device supports vendor reserved register _at_ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE NIC2600/11082195 (LD 1
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# First DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 5))
# Start dependent functions: priority acceptable
# *** ERROR *** No DMA channel specified!
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 4))
# End dependent functions
# Vendor defined tag: 72 00 01
(NAME "NIC2600/11082195[1]{National Instruments, AT-MIO-64E-3}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
>From: Frank Mori Hess <fmhess_at_users.sourceforge.net>
>To: comedi_at_comedi.org
>Subject: Re: init_setup() failed for AT-MIO-64E-3
>Date: Wed, 14 Jul 2004 07:44:27 -0400
>
>-----BEGIN PGP SIGNED MESSAGE-----
>Hash: SHA1
>
>On Tuesday 13 July 2004 02:18 pm, CARBAJAL Juan Pablo CINI wrote:
> > Hello all!
> >
> > I´ve been reading all what was post in the list about calibration
> > problems but i couldn´t find
> > any solution.
> > The problem i have is similar to the posted on
> > Wed, 01 Oct 2003 12:57:47 -0400
> > by
> > jose.3_at_wright.edu
> >
> > when I do
> > comedi-0.7.68# comedi_calibrate --file /dev/comedi0 --driver-name
> > ni_atmio
> >
> > I get
> >
> > init_setup() failed for AT-MIO-64E-3
>
>comedi_calibrate doesn't support your board yet. If you get comedilib and
>comedi from cvs, then comedi_calibrate should provide more useful
>information (enough to add proper support). The output of
>comedilib/demo/eeprom_dump would also be useful. And if you board is
>isapnp, I'd be interested in the output of pnpdump.
>
>- --
>Frank
>
>-----BEGIN PGP SIGNATURE-----
>Version: GnuPG v1.2.4 (GNU/Linux)
>
>iD8DBQFA9Ryb5vihyNWuA4URAoQ9AJsE/u73CYqzNo/q+iG1V3O98i2WKgCcDrkc
>5/pUHXPwvlZLQdEeExhdsKk=
>=NhXQ
>-----END PGP SIGNATURE-----
>
>_______________________________________________
>comedi mailing list
>comedi_at_comedi.org
>https://cvs.comedi.org/cgi-bin/mailman/listinfo/comedi
_________________________________________________________________
MSN Amor: busca tu ˝ naranja http://latam.msn.com/amor/
Received on 2004-07-19Z12:12:07