problems with usbdux

To Ian & Bernd 
 
I followed the suggestions and started fresh. 
The first time I installed and compiled kernel 
2.6.9. 
It did accept the usbdux and gave no errors when 
initalizing the card. 
In the dmesg below one can see some of the 
messages generated. The card is recognized and 
functions well but when trying to run ao_waveform 
the messages in the first part of the caption from 
dmesg shows time out and using of different 
addresses. I have tried all usb connections on the 
computer but to no awail. I get time out after a 
while. These messages in the beginning all comes 
from the 2.6.9. kernel. 
Then I compiled the 2.6.8.1-comedi kernel and the 
last part of dmesg registers the card but in spite 
of comedi.o present and in ldconfig it gives the 
error comedi.o not loaded. As I wrote earlier the 
card runs on other computers of several brands. 
In the other Dell computer an advantec 1710 board 
sits  and runs perfectly in Comedi. 
Would you have some more suggestions? 
The thing I have not tried is make clean partly 
since it is not written in the instructions on 
your homepage on how to install and run. 
 
usb 4-6: control timeout on ep0out 
ehci_hcd 0000:00:1d.7: Unlink after no-IRQ?  
Different ACPI or APIC settings may help. 
usb 4-6: control timeout on ep0out 
usb 4-6: device not accepting address 3, error 
-110 
usb 4-6: new high speed USB device using address 4 
usb 4-6: control timeout on ep0out 
usb 4-6: control timeout on ep0out 
usb 4-6: device not accepting address 4, error 
-110 
usb 1-1: new low speed USB device using address 3 
input: USB HID v1.10 Mouse [Dell Dell USB Mouse] 
on usb-0000:00:1d.0-1 
inserting floppy driver for 2.6.8.1-comedi 
Floppy drive(s): fd0 is 1.44M 
FDC 0 is a post-1991 82077 
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33) 
Uniform CD-ROM driver Revision: 3.20 
ide-floppy driver 0.99.newide 
NET: Registered protocol family 17 
b44: eth0: Link is down. 
b44: eth0: Link is up at 100 Mbps, full duplex. 
b44: eth0: Flow control is off for TX and off for 
RX. 
PCI: Setting latency timer of device 0000:00:1f.5 
to 64 
intel8x0_measure_ac97_clock: measured 49494 usecs 
intel8x0: clocking to 48000 
[drm] Initialized i830 1.3.2 20021108 on minor 0: 
Intel Corp. 82845G/GL[Brookdale-G]/GE Chipset 
Integrated Graphics Device 
mtrr: base(0xe8020000) is not aligned on a 
size(0x400000) boundary 
SCSI subsystem initialized 
st: Version 20040403, fixed bufsize 32768, s/g 
segs 256 
NET: Registered protocol family 10 
Disabled Privacy Extensions on device c035d8e0(lo) 
IPv6 over IPv4 tunneling driver 
eth0: no IPv6 routers present 
comedi: no version for "struct_module" found: 
kernel tainted. 
comedi: version 0.7.69 - David Schleef 
<ds_at_schleef.org> 
usbdux.c: v1.00pre10:Stirling/ITL USB-DUX -- 
Bernd.Porr_at_f2s.com 
usbcore: registered new driver usbdux 
 
Best regards! 
per

Received on 2005-03-03Z09:14:00