RE: Analog output cb_pcidas and das-1602/16 board

Woah.  Yeah chances are that the register layout is probably completely
different (which would explain your troubles with the driver).

I am going to dl the specs now... maybe I can annoy Ivan by submitting a
diseased and ugly patch to get your board working.. hehe :)

-Calin

On Fri, 24 May 2002, Curry, Timothy E  (Contractor-CRC) wrote:

> I am using the cb_pcidda.o driver. The comedi documentation section 5.7
> states that the 2 and 8 channels should work and I assumed that the 6
> channel should work, too. It is my understanding that the 6 channel version
> of this board is relatively new. I have the board specification if you need
> them or you can go to www.measurementcomputing.com and download the specs
> from their documentation section.
>
> Is my assumption correct?
>
> > >-----Original Message-----
> > >From: Ivan Martinez [mailto:imr_at_oersted.dtu.dk]
> > >Sent: Friday, May 24, 2002 7:46 AM
> > >To: Curry, Timothy E (Contractor-CRC); 'Calin A. Culianu';
> > >comedi_at_stm.lbl.gov
> > >Subject: Re: Analog output cb_pcidas and das-1602/16 board
> > >
> > >
> > >"6 channel version of this board"???. You posted about a
> > >DDA06/16, which I
> > >can't find in the list of supported hardware. Which driver
> > >are you using?.
> > >Ivan
> > >
> > >On Friday 24 May 2002 02:29 pm, Curry, Timothy E
> > >(Contractor-CRC) wrote:
> > >> Calin,
> > >> 	I tried the 6 channel version of this board and I was
> > >unsuccessful.
> > >> You can see from my message I sent out yesterday that I
> > >can communicate
> > >> with the board but it always goes to -5VDC when I command
> > >it. I am not
> > >> experienced enough with device drivers to figure out what
> > >is wrong. I hope
> > >> that someone on this reflector will see this message and
> > >look into this
> > >> problem for us.
> > >>
> > >> I will let everyone know the solution when I find one.
> > >>
> > >> Tim Curry
> > >>
> > >> > >-----Original Message-----
> > >> > >From: Calin A. Culianu [mailto:calin_at_ajvar.org]
> > >> > >Sent: Thursday, May 23, 2002 3:44 PM
> > >> > >To: comedi_at_stm.lbl.gov
> > >> > >Subject: Analog output cb_pcidas and das-1602/16 board
> > >> > >
> > >> > >
> > >> > >
> > >> > >Unfortunately I have yet to get a breakout box capable of
> > >> > >analog output...
> > >> > >but I was just curious, has anyone tested AO on this board
> > >> > >with the above
> > >> > >driver?
> > >> > >
> > >> > >I was reading the sourcecode to the analog output stuff and
> > >> > >it seems to be
> > >> > >following the register specs for the board to the letter, so
> > >> > >in theory
> > >> > >it should work.. but I was curious if anyone has
> > >actually tested it.
> > >> > >
> > >> > >Thanks,
> > >> > >
> > >> > >-Calin
> > >> > >
> > >> > >
> > >> > >
> > >> > >_______________________________________________
> > >> > >comedi mailing list
> > >> > >comedi_at_stm.lbl.gov
> > >> > >http://stm.lbl.gov/cgi-bin/mailman/listinfo/comedi
> > >>
> > >> _______________________________________________
> > >> comedi mailing list
> > >> comedi_at_stm.lbl.gov
> > >> http://stm.lbl.gov/cgi-bin/mailman/listinfo/comedi
> > >
>
>
> _______________________________________________
> comedi mailing list
> comedi_at_stm.lbl.gov
> http://stm.lbl.gov/cgi-bin/mailman/listinfo/comedi
>

Received on 2002-05-24Z14:47:47